Power supply troubleshooting steps help you find out whether a dead, restarting, or unstable computer is caused by its power supply unit, the box that converts wall electricity into the low-voltage power your parts need. Many symptoms look similar, so a careful sequence avoids wasted money on new parts.
Most of the checks below need only a screwdriver, a known-good power cord, and a little patience. Work through them in order, and stop as soon as you find the fault. Always unplug the computer before opening the case or touching internal components.
Recognize the Signs That Point to a Failing Power Supply
A failing power supply rarely dies all at once. Common warning signs include a PC that shuts off under load, restarts during gaming or video rendering, or fails to power on even though the fans spin briefly. Some units also make a burning smell, buzzing, or a clicking sound before they stop working.
Other symptoms can mimic a power problem, such as overheating, a faulty motherboard, or a bad memory module. Noting exactly when the problem occurs, whether at startup, under heavy load, or randomly, will help you follow the right troubleshooting path and avoid replacing a part that is not at fault.
Keep a simple log of what you see, including error messages, beep codes, and whether any lights come on. This record will be useful if you later contact the manufacturer or a repair technician, because it shows the pattern of failure instead of a single vague complaint.
If you see smoke, smell burning plastic, or notice swelling or leaking in the unit, stop using the computer immediately. Disconnect it from the wall and seek professional help, because a damaged power supply can cause a fire or damage other components.
Start With Safe Preparation Before Testing Anything
Before opening the case, turn off the computer, switch off the wall outlet or power strip, and unplug the power cord from the back of the power supply. Press the power button once after unplugging to drain residual charge from the internal capacitors. Working on a dry, non-carpeted surface reduces the risk of static damage.
Gather the tools you will need, typically a Phillips screwdriver, a flashlight, and a notepad for recording results. If you plan to touch internal parts, wearing an anti-static wrist strap is a good habit, though careful handling without one is usually acceptable for basic checks.
Check whether the wall outlet works by plugging in a lamp or another device you know is functional. Test the outlet before blaming the computer, because a tripped breaker, a loose outlet, or a faulty surge protector can mimic a dead power supply.
Also confirm that the power supply switch on the back of the unit is set to the correct position for your region’s power, and that the input voltage selector, if present, matches your outlet. A wrong setting can cause immediate failure, so verify it before powering on again.
Run Through These Basic Checks in Order
Begin with the simplest possible causes, since they are quick to rule out and cost nothing. Work through the following checks in sequence, testing the computer after each change so you know which step resolved the problem.
- Confirm the power cord is firmly seated at both the wall outlet and the power supply, and try a different cord known to work.
- Make sure the rear power switch on the power supply is turned on, and that the wall outlet is supplying power.
- Reseat the 24-pin motherboard connector and the 8-pin or 4+4-pin CPU power connector, pressing each until it clicks.
- Disconnect unnecessary internal devices, such as extra drives or add-in cards, to test whether a single component is drawing too much power.
- Check for loose screws, bent pins, or obvious damage on the connectors and on the power supply housing.
If the computer now starts and stays running, the cause was likely a loose connection or an overloaded setup. Reconnect your removed parts one at a time, testing after each addition, to identify any component that triggers the failure again. This method isolates the problem without guesswork and prevents unnecessary replacements.
Inspect Cables and Connectors for Physical Damage
Cables and connectors are a frequent source of intermittent power problems. Look for melted or discolored plastic around the pins, which indicates excessive heat from a poor contact. A connector that feels loose or does not lock firmly into its socket can cause brief power drops that look like a failing supply.
Examine the modular cables for bent or broken pins, frayed wires, or cracked insulation. Gently wiggle each cable at its connector while the system runs, if it is safe to do so, to see whether the computer shuts off. Any change in behavior points to a connection problem that should be corrected.
Verify that each cable is plugged into the correct socket on the power supply. Modular units often have separate ports labeled for the motherboard, CPU, graphics card, and drives, and mixing cables between units can damage components.
If you find damaged cables, replace them with cables designed for your specific power supply model. Using third-party or mismatched cables can cause unexpected voltage problems, so buy from the manufacturer or a reputable seller that confirms compatibility.
Test the Power Supply and Check Its Output
Testing the power supply itself can help confirm or rule out a fault. Two common methods are a paperclip test to see whether the unit starts without a motherboard, and a multimeter check of its output voltages. Both require caution, because the unit contains dangerous voltages even when unplugged.
Perform the Paperclip Test Safely
The paperclip test checks whether the power supply turns on by itself. Disconnect all components and the motherboard connectors, then bridge the green wire and a black ground wire on the 24-pin connector using a paperclip or jumper. Plug the unit in and flip the rear switch on. If the fan spins, the supply is at least partly functioning.
This test does not measure output quality, and a unit that spins its fan can still deliver unstable voltage. Perform it only if you are comfortable with the risks, and never open the power supply housing, because the internal capacitors can hold a dangerous charge for a long time after unplugging.
Measure the Output Voltages With a Multimeter
A digital multimeter can check the main rails on the 24-pin connector. Typical nominal values are about 12 volts, 5 volts, and 3.3 volts, and readings that fall well outside these targets suggest a problem. Measure with the unit powered on and the motherboard connected, touching the probes carefully to the correct pins.
Small deviations are normal, and a reading of a few percent off is usually acceptable. Larger drops that worsen under load, however, indicate that the power supply cannot keep up with demand. Record your readings so you can compare them across tests, and check the manufacturer’s specifications for the tolerance range of your model.
Use a Dedicated PSU Tester When Available
A dedicated power supply tester plugs into the motherboard and drive connectors and displays each voltage rail. These devices are inexpensive and easier for beginners than a multimeter, because they show clear indicators for each output. Choose a tester that supports the connector types your unit uses, and follow its instructions exactly.
Keep in mind that a tester checks basic presence and approximate voltage but cannot reveal every fault, such as ripple or problems that appear only under heavy load. A passing result is encouraging, yet it does not guarantee a stable supply, so combine tester results with the other troubleshooting steps.
Check Whether the Load Exceeds the Power Supply Capacity
A power supply that is adequate for light use can fail during gaming or heavy workloads if the total demand is too high. Symptoms include crashes or shutdowns that begin only when the graphics card or processor is stressed. Checking the wattage rating against the components installed in your system is an important part of troubleshooting.
Use a reputable online power calculator, or add up the rated power draw of your processor, graphics card, drives, and other parts, then leave headroom for peaks. Recommended headroom varies by manufacturer, so consult the documentation for your specific hardware instead of relying on a single rule.
Be sure the wattage printed on the label refers to the continuous output, not a peak figure. Some marketing emphasizes higher numbers, so compare the rating on the label to the requirements of your build. An undersized unit may need replacing even if it powers on.
If you recently added a more power-hungry graphics card or processor, the existing power supply may no longer be enough. Upgrading the unit to a higher, reputable model with the correct connectors is often the most reliable fix in this situation.
Know When the Power Supply Needs Replacing
If your tests show unstable or missing voltages, the fan does not spin, or the unit fails the paperclip test while connectors and cables are sound, the power supply likely needs replacing. Continuing to run a faulty unit can damage the motherboard, graphics card, and storage, so it is wiser to act promptly once the fault is confirmed.
When choosing a replacement, match the form factor to your case, usually ATX for standard desktops, and confirm that the connectors fit your components. Look for independent safety certification from recognized testing bodies and a warranty that covers the unit for several years, as these features indicate a higher build standard.
Before buying, check whether your current unit is still under warranty, since many manufacturers offer repair or replacement at no cost. Keep your receipt and the model number, because the process is faster when you have them ready.
After installing the new unit, test the system under normal use for several days and monitor temperatures and stability. A successful replacement should eliminate the restarts or shutdowns you previously experienced, and if the problem persists, the cause may lie with another component that deserves separate diagnosis.
Avoid These Common Troubleshooting Mistakes
Many people lose time or spend money on the wrong fix. Watch for the following errors, which often make the problem harder to diagnose or create new safety risks.
- Replacing the power supply before checking the outlet, cord, and switch, which wastes money on a healthy part.
- Using cables from a different power supply model, which can deliver incorrect voltages or fail to fit properly.
- Ignoring the wattage requirement and installing a unit too weak for a new graphics card or processor.
- Opening the power supply housing, where stored electrical charge can cause serious injury even after unplugging.
- Testing many changes at once, so you cannot tell which action actually resolved or caused the problem.
Changing one variable at a time and recording each result keeps the process clear. If you are uncertain at any stage, especially when a multimeter or internal access is needed, ask a qualified technician for help. Professional diagnosis costs less than replacing parts unnecessarily and protects you from electrical hazards.
Build Habits That Prevent Future Power Problems
Good maintenance reduces the chance of future failures. Keep the case vents and power supply fan free of dust by cleaning them periodically with compressed air while the computer is unplugged. Restricted airflow raises internal temperatures, which shortens the life of electronic components and can trigger shutdowns.
Connect the computer to a quality surge protector or a uninterruptible power supply, which shields the unit from voltage spikes and brief outages. Plugging a desktop directly into a wall outlet on a shared circuit with heavy appliances can also contribute to instability, so consider a dedicated outlet where practical.
When planning upgrades, calculate the total power requirement before buying new parts, and choose a power supply with some margin above that figure. Reviewing the manufacturer’s warranty and documentation at purchase time will also make future troubleshooting easier.
Keep a record of your computer’s model, power supply specifications, and any past service. This simple file helps you respond quickly when a problem appears and supports any warranty claim you may need to make later.